Maintenance & Technical > KX500 Original

Mudflap

<< < (2/4) > >>

sandblaster:

All the same

1986 Kawasaki KX125(KX125E1)
1987 Kawasaki KX125(KX125E2)
1987 Kawasaki KX250(KX250E1)
1987 Kawasaki KX500(KX500C1)
1988 Kawasaki KX125(KX125F1)
1988 Kawasaki KX250(KX250F1)
1988 Kawasaki KX500(KX500D1)
1989 Kawasaki KDX200(KDX200E1)
1989 Kawasaki KX125(KX125G1)
1989 Kawasaki KX250(KX250G1)
1989 Kawasaki KX500(KX500E1)
1990 Kawasaki KDX200(KDX200E2)
1990 Kawasaki KX500(KX500E2)
1991 Kawasaki KDX200(KDX200E3)
1991 Kawasaki KX500(KX500E3)
1992 Kawasaki KDX200(KDX200E4)
1992 Kawasaki KX500(KX500E4)
1993 Kawasaki KDX200(KDX200E5)
1993 Kawasaki KX500(KX500E5)
1994 Kawasaki KDX200(KDX200E6)
1994 Kawasaki KX500(KX500E6)
1995 Kawasaki KX500(KX500E7)
1996 Kawasaki KX500(KX500E8)
1997 Kawasaki KX500(KX500E9)
1998 Kawasaki KX500(KX500E10)
1999 Kawasaki KX500(KX500E11)
2000 Kawasaki KX500(KX500E12)
2001 Kawasaki KX500(KX500E13)
2002 Kawasaki KX500
2003 Kawasaki KX500 (KX500-E15)
2004 Kawasaki KX500 (KX500-E16)

1989kawasaki:
you should just paint an oem one black , but since you ordered an acerbis its too late to get oem  :cry: :cry:

sniper1:
        I have a ufo and acerbis in black for a 250 and they are twice the thickness of OEM a much higher quality part for starters and then I have everything in black and green and I might as well go all out coming as far as I have already.

sniper1:
        They are not all the same I have a UFO kx250 mud flap for a 91-92 kx 250 and it's too narrow then I have an acerbis mud flap for a 97 kx 250 and it's too narrow and when I say too narrow I'm talking 1.5" so I can't even drill a hole in them and make them work they are too small but bikebandit thought they were all the same too and so did cheap cycle parts but they have found out they are not the same and the only years kx250 mud flap that will fit the k5 are 88-89 according to a kawasaki dealership in michigan so I'm hoping they are right or this will be my 3rd kx250 mud flap that doesn't fit.

        Can you do me a favor 89kaw? can you measure your mudflap holes and tell me how far apart they are in inches if possible and if they are straight accross from each other or if the right side bolt is a little lower than the left looking at it from the rear.

The UFO flap I have is 3" center to center of the holes and my k5 is 5.5" from center to center of bolt holes same with acerbis it doesn't have the holes drilled but the entire flap is only 4" wide.

1989kawasaki:
i can get those measurements tommorow, cause i am not at home at the moment

Navigation

[0] Message Index

[#] Next page

[*] Previous page