KX Riders
  Home Help Login Register   *
Welcome, Guest. Please login or register.
Did you miss your activation email?
May 25, 2019, 10:18:08 PM

Login with username, password and session length
Recent
[Today at 09:39:25 PM]

[May 24, 2019, 04:55:17 PM]

[May 24, 2019, 01:07:30 PM]

[May 24, 2019, 09:33:14 AM]

[May 24, 2019, 06:08:16 AM]

[May 24, 2019, 12:48:08 AM]

[May 23, 2019, 03:48:47 PM]

[May 20, 2019, 06:26:58 PM]

by Pmcg
[May 20, 2019, 08:02:54 AM]

[May 20, 2019, 07:49:59 AM]

[May 19, 2019, 12:34:54 PM]

[May 19, 2019, 04:15:04 AM]

[May 18, 2019, 08:14:57 AM]

[May 17, 2019, 03:16:34 AM]

[May 15, 2019, 04:51:38 PM]
Pages: [1]   Go Down
  Print  
Author Topic: 1987 kx500 flywheel(rotor)  (Read 167 times)
0 Members and 1 Guest are viewing this topic.
Gage.Record
Newbie
*
Offline Offline

Joined: 05.01.19
Posts: 3


« on: May 06, 2019, 09:26:16 PM »

I went to pull the flywheel off of my 1987 kx500 and the puller I have bent the flywheel(rotor), Iím looking to buy a new one and have found a few but they are around $140. My question is, can I buy a cheaper one like a 250 flywheel from the same year or is that just completely wrong? The part numbers are close and they look very similar but Iím just not sure enough to buy one yet. Do you guys know what I need to be looking for and do you know a good place to buy a flywheel(rotor) that would fit my bike.
Logged
alward25
Hero Member
*****
Offline Offline

Joined: 12.12.08
Posts: 1,331



« Reply #1 on: May 08, 2019, 02:58:01 PM »

Sound like you did not use the correct puller.  A 3 jaw perhaps?  It is a little hard to find an 87 flywheel, but here is the best place to fin someone that might.  An buy the correct puller for the toolbox.
Logged

"Let there be light"
sandblaster
Global Moderator
Hero Member
*****
Offline Offline

Joined: 09.12.10
Posts: 7,914



WWW
« Reply #2 on: May 08, 2019, 10:13:58 PM »

Yes, those flywheels are sought after for SM and drag racing.
They won't be cheap.
I don't know of any 250 flywheel that will work with your stator.
You can bolt on a 250 stator and flywheel but you will need the matching CDI and coil.
Logged

The four stroke engine: That's one stroke for producing power and three for wearing the engine out.
Gage.Record
Newbie
*
Offline Offline

Joined: 05.01.19
Posts: 3


« Reply #3 on: May 11, 2019, 07:35:05 PM »

Thanks for the info guys, Iíll definitely buy the right puller and look into getting a flywheel up and running, looks like this whole bike is going to need to be rebuilt, just found a chip in the cylinder wall. 😩😩
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
TinyPortal v0.9.7 © Bloc
Valid XHTML 1.0! Valid CSS!
Page created in 0.169 seconds with 67 queries.