KX Riders
Maintenance & Technical => KX500 Original => Topic started by: hughes on March 09, 2005, 03:29:16 PM
-
What is everybody using to clean your chain and sprockets with after each ride :?: I have been using engine degreaser and a srub brush.
-
Jack Daniel's!!!!!!!!!!!! :lol:
I just blast it with the presure washer, then oil it....
I don't think it's the best thing to do, but it works for me!!!
:wink:
-
Most of the time a soft bristle brush so it wont tear the o-rings and some purple power and liquid dish soap mixed.I have hit the sides with a preassure washer once in a great while,but dont aim it a the o-rings,ypull wash out the grease.
-
I run std. 520 chains.
-
I use soapy water and a scrub brush. I just jack the rear wheel up and spin the rear wheel by hand holding the brush on the chain. Go around a few times on the inside and outside. Hose it off. Dry it off with a rag. Let it air dry a couple hours, and brush on some 90W gear lube. Let it sit overnight to drip off any excess oil. If your in a hurry to ride right away, just lightly wipe over the chain with a rag to take off the excess. I don't like sticky spray lubes; they always seem to collect dirt and they're a real P.I.T.A. to get clean. Spray lubes are all a gimick IMO; heavy gear lube works great.
-
Toml,
I agree with you about the spray lubes but I guess I am brain washed because I still use them. I will try the 90w gear oil it must clean up alot better. Is anybody using gold plated chains :?: If so do they keep their color or does the plating wear off :?:
-
I run O- Ring chains, so I blow the chain off with an air hose and WD - 40 it to displace any moisture! I guess my bike is lucky to almost never see any mud or water!
Alan the desert Rat! :lol:
-
I spend my time 50/50 between mud and sand. I run the best o-ring I can buy (Tsubaki) and then simply wire brush off the crud. When brushing, the chainlube I use (the white belray stuff) balls up and falls off taking most of the dirt with it. Re-lube and you're ready to go. Since I started avoiding the HP car wash, my chain/sprockets last forever; 5 years on the present set. I occasionally give it a shot of WD40 if the orings look dry. Cam.
-
On previous lower powered machines I've owned, 2 chains brought at the same time[non Oring] have been the my answer to preserved sprocket life. When chain number 1 was due for adjustment, itwould get pulled off and dumped into a container of WD40 and left untill number 2 chain was due for adjustment. Always run alloy sprockets. Seemed to get years of service out of them usiing a couple of chains. Plus when you pull them out of the WD and give them a bit of a wipe over, the good old gold Regina looked great. Worked for me. Dunno about the dirty 5 tho. Spose a good quality 520 may handle it? Noticable power sucking from Oring to non oring. On the Ducati there was quite a difference in power between the two. Always raced with standard 520. Lubed with Motul. But all good till they are washed off in the first river crossing! Any body seen Scottoiler? My old Norton had its own chainluber in the form of a rubber hose with an adjustable tap which would clamp on and regulate a flow of oil to the chain. Never changed a chain on that old thing. Sprocket was cast as part of the rear hub. The Poms aye? Ahh just joking! :lol:
-
Anyone ever try bar and chain oil on their chains??? I was reading a bottle in the store; and it says it has a sticky additive to reduce fling-off. It's made for chains and it's cheap as dirt!!! Sounds good to me!!! What do you guys think???
-
On a non o-ring chain that may work o.k. Give it a try and let us know what you think,Id lube it while the chain was warm from use.
-
Anyone ever used that stuff from MX1000.com?
-
Anyone ever used that stuff from MX1000.com?
I believe it is for non-oring chains only, or mainly. I know that from Jaybird always knocking on O/X ring chains. I'll be honest and say I'm a major slacker when it comes to chains. I'm horrible and NEVER clean my chain and bearly lube it. Which it is a Did Xring. It has lasted roughly 8 months so far, doesn't even look like it has worn any at all.
-
Wow, I really like the bar and chain oil!!! I used some of my Grandfather's craftsmen (30w I think) red stuff yesterday. You can tell it's a bit tacky cuz it's kind of stringy when you brush it on. After mud riding for 4 hours yesterday, my chain didn't even look very dirty. I just hosed it off and it came perfectly clean. Even cleaner than when I lubed it!!! It totally penetrated and displaced the old dirt that was still there from the previous ride!!!
-
I've been using an RK Gold o-ring chain (not cheap) and Renthal sprockets for two years now. I wash my chain along with the bike and spray it with WD-40 when I get done. I can't remember the last time I had to adjust it and it still looks great.
-
I just got a new Primary Drive sprocket and X-ring set up from Rocky Mtn. Haven't got it on yet though. But I'm not anal about chains either. Might just use motor oil like in the old days. Seemed to work OK then.
-
Ok guys, this is my pitch for O-Ring chains!
I sell and service exercise equipment and lots of the high end health club stuff uses # 40 chain and of course bikes, steppers etc. What I see happening over the life of the equipment is that, the chain that is well maintained and lubed often needs very little adjustment. Those that are let go for long periods of time need frequent adjustment and they eat the sprockets up! So I conclude that the chain that is let go wears and stretches and eats the sprockets up!
Now when it comes to motorcycle chains I prefer O - Ring chain because unlike regular chain all you really have to do is keep it clean! You do not have to use lubes that attract dirt and sand that wear out the chain. I am lucky because I almost never ride in anything but sand and all I have to do is blow of my bike with an air hose. When I do wash it I spray the chain off with WD-40 to displace moisture.
When I first got my 01 KX5 I was adjusting the chain almost every time I rode it! I replaced it with a O - Ring chain adjusted it once after the first ride and haven't adjusted it since!
Alan
PS I love fact that the exercise equipment manufactures are to cheap to use o - ring chains, It would really cut into my repair Business! :lol:
-
One of the recommended fluids for cleaning O-ring chains it paraffin.
-
One of the recommended fluids for cleaning O-ring chains it paraffin.
Are you refering to chain wax?