| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
| 0 Members and 18 Guests are viewing this board. | ||||
|
|
15 Replies
5,763 Views |
April 13, 2006, 06:05:30 AMby doordie |
|
|
|
Piston-cylinder clearance
Started by Pvo |
14 Replies
5,756 Views |
September 02, 2010, 03:37:22 PM by YUNGGUNNAZ |
|
|
|
Needsome thought's Fly wheel
Started by IcemanK5 |
12 Replies
5,745 Views |
February 18, 2010, 01:44:53 PM by kx5rider |
|
|
|
Best timing for '90 k5?
Started by NZ500 |
12 Replies
5,744 Views |
October 15, 2010, 02:50:04 AM by martinfan30 |
|
|
|
Aparent chain wear into my left case.
Started by Hawkeye58 |
14 Replies
5,738 Views |
April 23, 2017, 02:05:36 PM by Hawkeye58 |
|
|
|
10 Replies
5,738 Views |
May 01, 2007, 07:16:23 AM by demographic |
|
|
|
|
15 Replies
5,731 Views |
January 13, 2005, 01:04:48 AM by Minnetonka_Mark |
|
|
|
|
sleeve/cylinder deck height question
Started by 2001KX5 |
7 Replies
5,729 Views |
May 05, 2006, 08:41:58 AM by 2001KX5 |
|
|
|
Flywheel
Started by Rick |
3 Replies
5,728 Views |
February 10, 2003, 04:49:27 AM by Hogwylde |
|
|
|
1986 kx 500 will not start
Started by robert40215 |
13 Replies
5,711 Views |
March 17, 2007, 04:13:57 PM by MadKaw |
|
|
|
low gear output 13129-1180
Started by valver501 |
10 Replies
5,708 Views |
October 30, 2015, 03:49:43 AM by sandblaster |
|
|
|
pre mix oil
Started by mikesmith |
14 Replies
5,704 Views |
June 04, 2004, 05:39:26 PM by toddwunsch |
|
|
|
Getting started project KX5 in 06 Aluminum frame
Started by hangtime |
13 Replies
5,703 Views |
November 13, 2006, 07:16:27 AM by hangtime |
|
|
|
kx5 biggest bore
Started by YUNGGUNNAZ |
12 Replies
5,701 Views |
October 18, 2005, 12:40:49 AM by YUNGGUNNAZ |
|
|
|
16 Replies
5,696 Views |
May 24, 2012, 07:46:00 AM by kwakman |
|
|
|
|
Whats the compatibal years
Started by chrisxj |
11 Replies
5,696 Views |
September 01, 2011, 12:44:35 AM by kwakman |
|
|
|
15 Replies
5,693 Views |
February 23, 2011, 09:54:19 AM by maddoggy |
|
|
|
|
K5 Moto Monster
Started by Norway |
12 Replies
5,693 Views |
August 12, 2005, 12:47:26 PM by Kawadougie |
|
|
|
KX250 CDI/Stator/Flywheel On the KX500
Started by kkvslayer |
4 Replies
5,689 Views |
July 12, 2012, 01:41:44 AM by kkvslayer |
|
|
|
Your thoughts on flywheel weights?
Started by Polar-Bus |
14 Replies
5,684 Views |
June 05, 2006, 02:36:26 AM by 5dracing |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic