| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
| 0 Members and 4 Guests are viewing this board. | ||||
|
|
Need a little help from a 500 owner.
Started by rummerd |
5 Replies
2,332 Views |
October 05, 2007, 03:02:07 PMby Uzi9mm |
|
|
|
Rear Wheel Offset
Started by CSAR FE |
0 Replies
2,331 Views |
October 11, 2018, 09:07:31 AM by CSAR FE |
|
|
|
kx rebuild
Started by blockhead ed |
5 Replies
2,331 Views |
January 27, 2011, 06:58:43 AM by 1989kawasaki |
|
|
|
Is this piston good?
Started by JustinSB |
6 Replies
2,330 Views |
September 17, 2009, 05:11:34 PM by JustinSB |
|
|
|
1989-04 KX500 Power valve, again
Started by Dad of Alf |
3 Replies
2,330 Views |
November 30, 2019, 12:46:21 PM by sandblaster |
|
|
|
Jetting for 90 ft above sea level
Started by Plymouthrider |
4 Replies
2,329 Views |
September 19, 2012, 11:14:59 AM by Plymouthrider |
|
|
|
Maintenance Questions
Started by 2-Stroke Tom |
2 Replies
2,329 Views |
April 21, 2009, 04:08:24 PM by 2-Stroke Tom |
|
|
|
carb help??
Started by seff23 |
2 Replies
2,328 Views |
April 10, 2009, 03:52:30 AM by seff23 |
|
|
|
frame interchange
Started by 500freak |
2 Replies
2,326 Views |
August 07, 2009, 07:15:37 AM by Motorrad |
|
|
|
somewhat low compression and squish?
Started by 1980mcneil |
5 Replies
2,325 Views |
August 31, 2020, 11:51:30 AM by 1980mcneil |
|
|
|
Been out of the parts availability loop
Started by Polar-Bus |
6 Replies
2,324 Views |
April 09, 2021, 12:31:51 PM by Polar-Bus |
|
|
|
finally almost done.
Started by mlstoner660 |
3 Replies
2,324 Views |
September 06, 2011, 03:04:30 PM by mlstoner660 |
|
|
|
Bike is running rich now
Started by dmg |
3 Replies
2,323 Views |
February 01, 2009, 04:48:26 PM by KXcam22 |
|
|
|
Kx 500 actuator seal newbie question
Started by JVUKrider |
0 Replies
2,323 Views |
July 01, 2017, 11:23:59 AM by JVUKrider |
|
|
|
1987 Kx500 engine parts
Started by NightTrain |
1 Replies
2,320 Views |
March 02, 2017, 05:37:53 PM by sandblaster |
|
|
|
4 Replies
2,320 Views |
April 22, 2011, 04:08:05 AM by greencannon |
|
|
|
|
where to buy n82r needle
Started by HK_Shawn |
2 Replies
2,320 Views |
November 21, 2009, 12:00:34 PM by KXcam22 |
|
|
|
best plastic manufacturers
Started by bilger69 |
5 Replies
2,320 Views |
November 29, 2011, 07:37:41 PM by Tumbleweed |
|
|
|
WANTED: kx500 engine
Started by reknelb |
3 Replies
2,318 Views |
January 09, 2004, 04:13:19 AM by kawdude |
|
|
|
4th gear wheelie up Olds gone bad (Glamis)
Started by afritts4u |
3 Replies
2,317 Views |
February 17, 2006, 03:24:23 PM by gowen |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic